binder system
英 [ˈbaɪndə(r) ˈsɪstəm]
美 [ˈbaɪndər ˈsɪstəm]
活页式账簿
双语例句
- Conventional stabilizers are added to the binder system as will be discussed below.
如下面将要讲的，粘合剂系统中加入惯用的安定剂。 - When the force of pigment absorbing binder is strong and binder system surface tension of the binder system is small, the film bonding strength is great.
当颜料对胶粘剂吸附力强，同时胶粘剂体系的表面张力小时，则涂层粘胶强度大。 - The production of hairdressing scissors which are produced by a metal injection moulding route, using a 440 type hardenable stainless steel powder and a PEG/ PMMA composite binder system has been investigated.
用金属粉末注射成型的方法制备高硬度合金剪刀，其喂料使用440型不锈钢粉末和PEG/PMMA复合粘结剂制成。 - Besides, a formula predicting chloride diffusion coefficient is used to evaluate the resistance to chloride ion permeability of concrete with different binder system, and the data obtained from this calculation are taken to compare with the experiment results.
研究中，还运用氯离子扩散系数的预测公式，对试验中采用的各种类型的混凝土进行了抗氯离子渗透性能的评价，比较了试验结果与计算结果之间的差异。 - The results show that in the binder system, organic polymer component and content have a great influence on the thermal properties of binder and feedstock such as binder melting point, decomposition temperature degradation curves.
研究结果表明，粘结剂组成对粘结剂和喂料的热性能如熔点、热分解温度和热分解曲线有很大的影响。 - The effect of three kinds of catalysts, ferric acetylacetonate ( Fe ( AA) 3), dibutyltin dilaurate ( T 12) and triphenyl bismuth ( TPB), on curing catalysis of HTPB propellant binder system is investigated.
研究了乙酰丙酮铁（Fe（AA）3）、二月桂酸二丁基锡（T－12）和三苯基铋（TPB）三类催化剂对丁羟（HTPB）推进剂粘合剂体系固化催化性能的影响。 - The binder system about cationic guar gum is most active field of research.
阳离子瓜尔胶的新式捆绑系统是研究的热点。 - Study on curing process of PET/ N100 binder system via FTIR(ⅱ)& study on the kinetics of TIR
PET/N100粘合剂体系固化过程FTIR研究（Ⅱ）&TIR的动力学研究 - To improve the mechanical properties of the binder system, a novel azido poly-isocyanate energetic curing agent ( EC) was synthesized via additional reaction of azido polyether polyol and hexamethylene diisocyanate ( HDI).
为提高黏合剂体系的力学性能，通过叠氮聚醚多元醇与六亚甲基二异氰酸酯（HDI）反应合成了一种新型叠氮多异氰酸酯含能固化剂（EC）。 - Pigment system, binder system and solid contention of coating. The coating technology formula is obtained. The relationship of coating layer microscopical structure and the physical index is analysed.
本文研究了颜料、胶粘剂以及涂料固含量对草浆轻量涂布纸性能的影响，得出了轻量涂布纸的涂料工艺配方，并分析了轻量涂布纸涂层的微观结构与宏观物理指标的关系。 - The binder system can meet the demand of the zirconia powder ( the average size of 0.8l μ m) selected in the experiment.
实验所用的粘结剂体系能够满足氧化锆粉末（平均粒度为0.8μm）对CIM粘结剂的要求。 - Development of Novel Binder System for Plasticizing Powder Extrusion Molding
增塑粉末挤压成形用新成形剂的研制 - The experimental results show that TPB is an ideal curing catalyst of HTPB propellant binder system.
实验结果表明，TPB是丁羟推进剂粘合剂体系比较理想的固化催化剂。 - On the other hand, the higher the energy of the binder system, such as an increase in the content of NG or in the nitrification degree of NC, the greater the burning rates of the propellant.
而含能粘结剂&DB母体的含能程度越高，即NG含量增加，或NC的硝化度加大，都有利于提高推进剂的燃速。 - Study on curing catalysis of HTPB propellant binder system
丁羟推进剂粘合剂体系固化催化研究 - A new cold-box binder system for CO 2-cured phenolic resin was introduced. This binder system consists of alkaline phenol-formaldehyde, hardening promoter and additive, etc. After CO 2 gas passed through the resin sand for hardening, then higher initial and final strength can be achieved.
介绍了一种新型CO2硬化碱性酚醛树脂冷芯盒粘接剂系统，由碱性酚醛树脂和促硬剂及添加剂等组成，吹CO2气体硬化后，获得具有较高初强度和终强度的树脂砂芯。 - The results show that the kinetic parameters of PET/ N100 binder system at different test conditions were consistent by using the integration method, derivative method and the iso-conversion rate method. The integration method is superior to the other two methods by comparison of linear correlation coefficient.
结果表明，积分法、微分法和等转化率法3种动力学参数处理方法获得同一体系不同试验条件下的动力学参数基本一致，从线性相关系数r比较，积分法优于其它两种方法。 - Study on preparation technology of the cathode in mcmb/ aqueous binder system for lithium ion battery
MCMB/水性粘结剂体系锂离子电池负极制备工艺研究 - The Development of CO_ 2-Cured Binder System as Co ld-Box Process Used in Foundry
铸造用CO2硬化冷芯盒材料及工艺的发展 - For vacuum worm type extrusion press, the physics essence of plasticizing powder extrusion molding ( PEM) process based on a novel binder system, and using cemented carbide powder as a test material, has been analyzed.
以硬质合金材质体系为对象，针对目前主要的一类挤压成形设备&真空螺杆挤压机，开发出了一种增塑粉末挤压成形新技术。 - Research Progresses of Energetic Binder System Used in Solid Propellants
固体推进剂用含能黏合剂体系研究进展 - In this work, the effect of performance of precoated paper on physical properties of the finished products was studied by changing precoating formula, namely pigments combination and binder system.
通过变化预涂配方的颜料组合和胶粘剂体系，考察了预涂纸对成纸物理性能的影响。 - The influence of added way of catalyst and inhibitor on the pot life of casting PBX was evaluated by testing the viscosity of the HTPB TDI binder system. A proper proportion between T-12 and HAA was found to be 4 ∶ 1.
通过测定HTPB-TDI黏结剂体系的黏度，评价了加入催化剂和抑制剂方式对浇注PBX黏结剂体系的适用期的影响，找出合适的T-12与HAA摩尔比为4∶1。 - An intensifier named STR with active groups is added to enhance curing network of HTPB and TDI binder system.
采用一种被称为STR的活性基增强剂来增强HTPB、TDI粘合剂体系的固化网络。 - Worm powder extrusion molding ( PEM) technology of hardmetal powder using novel binder system has been probed into.
探讨了用于硬质合金粉末螺杆挤压成形技术的新粘结剂制备及挤压棒的组织形貌。 - Test results on the influence of binder system on castable performance of spray gun shows different binder system has different influence at certain temperature range. And as a whole the cement and ρ-Al2O3 composite binder is the best.
结合体系对喷枪浇注料性能的影响：不同结合体系在不同温度段对喷枪浇注料性能有不同的影响，本试验结果证明，以水泥和ρ-Al2O3按1：4的比例复合加入为最佳。 - The main conclusion as follows: ( 1) There is an increase in alkalinity of red mud-cement binder system pore solution with the increase dosage of Bayer red-mud. But red mud would not increase the late alkalinity of binder system pore solution.
主要结论如下：（1）赤泥-水泥胶凝材料体系水化产物的孔溶液碱度随赤泥掺量的增加而增大，但掺入赤泥并不会引起胶凝材料水化后期孔溶液碱度的增加。